was added to the project list.
×

System components

BEGA Control consists of various system components. A technical description of all system components is provided below, so that you can ensure your system planning meets the various requirements. All components are compatible and can be configured individually.

For user-friendly configuration and management of lighting control, download our BEGA software. This allows you to easily program and parameterise customised control programs.

Übersicht der BEGA Control Software
 



DALI display

Touch display for configuring and controlling two DALI lines and 99 sequences.
Time-dependent controls can be implemented and TW and CC luminaires can be controlled.

for flush installation
Installation frames for DALI Display


DALI touch panel

DALI touch panel is a multifunctional user terminal with a replaceable user interface for controlling luminaires with a DALI interface. For the manual control of LED, tunable white and RGBW luminaires.

for wall mounting


DALI rotary dimmer

DALI rotary dimmer for LED luminaire control. For switching and adjusting the brightness of DALI luminaires, for controlling tunable white luminaires (DT8) or RGB luminaires (DT8).

for installation in switching and cavity boxes


DALI cross switch

Functions such as groups, scenarios and staircase control can be assigned to the cross switch with four pushbuttons via the DALI Cockpit software. Suitable for tunable white (TW) and colour control (CC).

for installation in switching and cavity boxes


DALI motion and light sensor

DALI motion and light sensor
Passive infrared motion and light sensor for indoors which responds to movement. Vertical opening angle of +/- 46°, horizontal opening angle of +/- 51°. Range of twelve metres. The measuring range of the light sensor is between 0 and 2500 lx. Configuration is carried out via the DALI Cockpit software.

DALI light sensor
Sensor for indoors with a measuring range of between 0 and 2500 lx. Threshold values for performing switching commands can be set in the DALI Cockpit software.

for flush installation


DALI programmer

DALI programmer for the configuration of DALI devices.
Four buttons can be programmed with DALI parameters.
The configuration and parametrisation of the component is carried out conveniently in the BEGA Tool app.

DALI programmer


DALI USB interface

Connection of the PC/laptop where the DALI Cockpit programming software is located to the DALI bus. Only required for programming.

for installation in switching and cavity boxes
for DIN rail mounting


DALI power supply

Power supply for the DALI operating devices and the control devices.

for installation in switching and cavity boxes
for DIN rail mounting


DALI repeater

Enables the maximum cable length to be extended from 300 metres (DALI line) to 600 metres. Extension using a repeater is only possible once per DALI line.

for DIN rail mounting
in housing · Protection class IP 65


Bluetooth DALI gateway

For the commissioning and power supply of DALI operating devices and control components in a DALI line with max. 64 devices.

for DIN rail mounting


DALI switch actuator

For relay contact control via the DALI bus.

for installation in switching and cavity boxes

for DIN rail mounting


KNX/DALI gateway · IPAS

KNX/DALI gateway IPAS for integrating 64 luminaires with a DALI operating device in a KNX system. Configuration of 16 DALI groups, of 16 DALI lighting scenarios, and of 16 sequences by means of an application program in the ETS software. DALI colour light control of tunable white and RGBW luminaires (DT8, RGBWAF, xy) can also be implemented in this way.

for DIN rail mounting


DALI switch module

Module for connecting four conventional pushbuttons or switches to control DALI operating devices.

for installation in switching and cavity boxes


DALI pushbutton module

Module for connecting four potential-free pushbuttons or switches to control DALI operating devices.

for installation in switching and cavity boxes


DALI daylight module

Control device for tunable white luminaires. Emulates the daylight curve (circadian curve). During the course of the day, the light is automatically controlled to be warmer or colder: warmer light in the morning and evening hours, colder light at noon time.

for installation in switching and cavity boxes


DALI sequencer module

Program for storing four independent sequences that can be started via DALI control elements, such as the DALI timer, DALI control module for four pushbuttons/switches or DALI cross switch.

for installation in switching and cavity boxes


DALI timer

For timer functions with up to 14 entries for calling up lighting scenarios for LED, tunable white and RGB W luminaires (DT6, DT8, RGBWAF, xy).

for installation in switching and cavity boxes


DALI power reducer

Control unit for automatic power reduction/night-time brightness reduction with integrated DALI power supply for up to nine standard DALI loads.

for installation in switching and cavity boxes


DALI operating devices for RGB/RGB W luminaires

Using the operating devices, it is possible to integrate RGB in-ground luminaires or RGB W swimming pool luminaires in DALI systems. Additive colour mixing can be effected using any commercially available DALI colour light control system.

inside housing · Protection class IP 65


Zigbee control modules

Relay output with a maximum switching capacity of 3,600 VA.
Connected loads are integrated into the Zigbee system using the control module and can thus be controlled via ZigBee control elements. Control modules with 1-10 V and DALI outputs are available.
Maximum radio range: 30 metres (open field).

for DIN rail mounting
for DIN rail mounting · with dimming output

for installation in switching and cavity boxes
for installation in switching and cavity boxes · with dimming output
for installation in switching and cavity boxes · with DALI interface


Zigbee router module

Signal amplifier for extending the maximum radio range (30 metres within a free field) between two components.

for installation in switching and cavity boxes


Zigbee pushbutton modules

Two-fold pushbutton module for connecting two potential-free pushbuttons. Four-fold pushbutton module for connecting four potential-free pushbuttons. The four-fold pushbutton module also supports colour control (CC) and tunable white (TW).

for installation in switching and cavity boxes


BEGA Gateway

Connecting the WLAN world to the Zigbee world. This means that the Zigbee system can be controlled by smartphone or tablet PC. Time-dependent actions can also be set. The gateway is configured via the web interface. The Zigbee system is configured via the BEGA Gateway app (Android or iOS).
Maximum radio range: 30 metres (open field).

BEGA Gateway


LCN USB port

The port is used to connect the PC and LCN system and is required for programming.

for DIN rail mounting


LCN/DALI Gateway

Gateway for connecting the LCN world to the DALI world. This means that DALI luminaires can be controlled using LCN control elements and sensors. A control module is required for connection. Maximum number of DALI devices: 64.

for DIN rail mounting


LCN control modules

Modules for integrating luminaires or other additional components into the LCN system – for example, LCN relay, LCN pushbutton/binary adapter, LCN/DALI gateway. The control module has a switching output, a DALI interface and a 1-10 V interface.

für Hutschienenmontage
im Anschlusskasten für den Einbau in Lichtmaste
im Gehäuse für die Verwendung außerhalb der Leuchte


LCN motion sensor

Passive infrared sensor which responds to movement and performs the programmed action. It has an opening angle of 110° and a range of ten metres.

für den Einbau in BEGA Lichtmaste
für Aufputzmontage
für Wandmontage im Innenbreich
für Deckenmontage im Innenbreich


LCN light sensor

Sensor for measuring the degree of ambient illuminance. The measured value can be used in the BEGA-PRO software as required. Threshold values for switching lighting on and off can be specified. The LCN light sensor and LCN motion sensor are frequently used in combination.

für den Einbau in BEGA Lichtmaste
für Aufputzmontage
für Wandmontage im Innenbreich


LCN pushbutton/binary adapter

Adapter with four inputs that can be optionally assigned with external pushbuttons or external binary contacts (such as timers). The processing of commands is set in the BEGA-PRO software. A control module is required for connection.

für Hutschienenmontage


LCN relay

Relay optionally equipped with two or eight changeover contacts. Used to switch loads. Programming is carried out via the BEGA-PRO software. A control module is required for connection.

für Hutschienenmontage


LCN buffer amplifier

Amplifier for preventing accidental energisation in distribution networks. In distribution networks with several earth fault circuit breakers, each circuit breaker must be equipped with its own buffer amplifier in order to separate the data line. If LCN buffer amplifiers are used in several distribution networks, connection is effected by means of segment couplers (LCN-LLG or LCN-LLK).

für Hutschienenmontage


LCN sensor module and LCN pushbutton adapter

Combination for integrating up to eight conventional pushbuttons in an LCN system. The pushbuttons are assigned via the BEGA-PRO software.

For installation in switching and cavity boxes:
LCN-Sensormodul
KNX/LCN-Tasteradapter
LCN-Tasteradapter 8-fach
Netzteil für KNX/LCN-Tasteradapter


LCN operating devices for RGB/RGB W luminaires

Using the operating devices, it is possible to integrate RGB in-ground luminaires or RGB W swimming pool luminaires in BEGA Control · LCN systems.

im Gehäuse · Schutzart IP 65